How to Install Tripleo(Openstack on Openstack) UnderCloud on CentOS 7

Install-undercloud-centos7

Undercloud is a single node OpenStack installation deployed either in a Virtual machine or in bare metal server. The objective of undercloud is to install, test, manage and update its overcloud servers (Controller, Compute & Storage nodes). In Red Hat terminology undercloud is known as “Director“. Undercloud basically contains all the images that is required to deployed Overcloud Controller, Computes, Swift and Storage.

Overcloud is the actual functional cloud for any organization where all the Virtual Machines are created on compute nodes and handle all the workloads. In other words we can say overcloud provides the openstack services like Nova, Keystone , Horizon, Neutron, cinder, Glance, Heat & Ceilometer Services.

In this article we will demonstrate how to install TripleO undercloud or Director on CentOS 7 VM.

Following are the minimum system requirements for undercloud:

  • 16 GB RAM
  • 1 Quad Core CPU
  • 80 GB disk Space
  • 2 Nics
  • CentOS 7.x / RHEL 7.x

Below are my lab setup details:

  • CentOS 7 VM (Minimal Installation) is hosted inside the KVM hypervisor.
  • Two Interfaces are attached to VM (Provisioning & NAT)
  • Provisioning Network: 192.168.126.0/24
  • NAT Network: 192.168.122.0/24
  • IP Address on eth0 is 192.168.122.90 and IP Address on eth1 is 192.168.126.1

To successfully install undercloud inside a virtual machine, you have to enabled Nested Virtualization in KVM hypervisor, if you not sure how to enable it, refer the below:

Let’s jump into the CentOS 7 VM and follow the below Steps:

Step:1) Set the Hostname and update /etc/hosts file

Run the hostnamectl command to set the hostname,

[[email protected] ~]# hostnamectl set-hostname "undercloud.example.com"
[[email protected] ~]# exec bash
[[email protected] ~]#

Add the following entries using the beneath command:

[[email protected] ~]# echo "192.168.126.1    undercloud.example.com" >> /etc/hosts

Update your system using below yum command and reboot once.

[[email protected] ~]# yum update -y && reboot

Step:2) Create non-root user (stack)

Run the beneath commands one after the another to create stack user and assign sudo rights to it. We will install undercloud using stack user only.

[[email protected] ~]# useradd stack
[[email protected] ~]# echo "enter_password_here" | passwd --stdin stack
[[email protected] ~]# echo "stack ALL=(root) NOPASSWD:ALL" | sudo tee -a /etc/sudoers.d/stack
stack ALL=(root) NOPASSWD:ALL
[[email protected] ~]# chmod 0440 /etc/sudoers.d/stack
[[email protected] ~]# su - stack
[[email protected] ~]$

Step:3) Enable required repositories for undercloud

Execute the below commands to enable and configured required repositories for undercloud installation.

[[email protected] ~]$ wget https://trunk.rdoproject.org/centos7/current/python2-tripleo-repos-0.0.1-0.20190328140951.a7bc8dc.el7.noarch.rpm
[[email protected] ~]$ rpm -ivh python2-tripleo-repos-0.0.1-0.20190328140951.a7bc8dc.el7.noarch.rpm
[[email protected] ~]$ sudo -E tripleo-repos -b rocky current
[[email protected] ~]$ sudo yum -y install yum-plugin-priorities
[[email protected] ~]$ sudo yum install epel-release -y

Note : We can check the latest version of python2-tripleo-repos from RDO repository

Step:4) Install TripleO CLI package using yum command

[[email protected] ~]$ sudo yum install python-tripleoclient -y

Step:5) Copy & edit “undercloud.conf” sample file that suits to your env

[[email protected] ~]$ cp /usr/share/instack-undercloud/undercloud.conf.sample ~/undercloud.conf

Now edit ‘undercloud.conf‘ that suits to your environment, In my case I am adding the following content under “Default” Section

[[email protected] ~]$ vi undercloud.conf
[DEFAULT]
local_ip = 192.168.126.1/24
undercloud_public_vip = 192.168.126.2
undercloud_admin_vip = 192.168.126.3
local_interface = eth1
masquerade_network = 192.168.126.0/24
dhcp_start = 192.168.126.100
dhcp_end = 192.168.126.150
network_cidr = 192.168.126.0/24
network_gateway = 192.168.126.1
inspection_iprange = 192.168.126.160,192.168.126.199
generate_service_certificate = true
certificate_generation_ca = local
………………………………

Save and exit the file.

Step:6) Start undercloud installation using openstack command

Now start undercloud installation using below openstack command,

[[email protected] ~]$ openstack undercloud install

Once the installation is completed successfully, we will get the output something like below

Undercloud-installation-completed-message

Verify the OpenStack Service list

[[email protected] ~]$ source stackrc
(undercloud) [[email protected] ~]$ openstack service list
+----------------------------------+------------------+-------------------------+
| ID                               | Name             | Type                    |
+----------------------------------+------------------+-------------------------+
| 19f1261745004b31bc77dcb17a5ed4f5 | heat-cfn         | cloudformation          |
| 1bdd5dfbc36f444ebe62580d71f1a7ec | heat             | orchestration           |
| 2b39423f188b412d85bed43f112b35d7 | zaqar-websocket  | messaging-websocket     |
| 46f64d65be874718a1b2c123f588371b | keystone         | identity                |
| 605261da43d64395b72acc5309a22096 | mistral          | workflowv2              |
| 6f50fb704b224c1abc3c2a1a163eb73a | neutron          | network                 |
| 7110b7d7711a4aa1af6a3c13566be28f | zaqar            | messaging               |
| 7e41468745724ecfa8ed339137e8b700 | placement        | placement               |
| 853efa8a8acf403b827617725c3b7322 | ironic-inspector | baremetal-introspection |
| a5522e5df77343b99a0e47812323a17b | swift            | object-store            |
| b9bbb1a771704b57a0833d738bfb86e5 | glance           | image                   |
| d50fdfa25fb64c3e865c172754452ab1 | ironic           | baremetal               |
| e2ea283690c742d3a98bd1eae6f9b830 | nova             | compute                 |
+----------------------------------+------------------+-------------------------+
(undercloud) [[email protected] ~]$

This confirms that undercloud has been installed successfully. In the next article we will demonstrate how to import overcloud images in under cloud and how to create inventory file for overcloud servers and then we will see how we can deploy overcloud servers via undercloud.

Read More on: How to deploy TripleO Overcloud (Controller , Compute) on CentOS 7 VMs

In case this article helps you to understand how to install undercloud on CentOS 7 VM, please do share your feedback and comments.

Posted by WordPress Guru